Home > Fuser Error > Lexmark Fuser Error Codes

Lexmark Fuser Error Codes


Remove toner cartridge for better access to jammed paper. If still error, you need replace heat roller. Replace the transfer roller as necessary. The follwing are the most common problems that can cause a Low heat error. weblink

While you have the fuser out, you should check the condition of the unit. Importantly is you must make sure it secure with the hot roller. Error 930 The wrong printhead is installed. vovanfun 34.194 προβολές 16:42 Vídeo Recarga Toner Lexmark E260 | E360DN | E460DN - Vídeo Aula Valejet.com - Διάρκεια: 4:06. http://support.lexmark.com/index?page=content&id=SO1583

924.01 Service Fuser Error Lexmark

Leave the printer off for at least 10 seconds before turning it back on. Check connections to the to interconnect card assembly. Error 25 Input sensor made at wrong time. Service Error Codes Other Troubleshooting Tips 200 Paper Jam T65X Troubleshooting 201 Paper Jam Power Issue with Input and Output Options Installed 80 Scheduled Maintenance The Difference Between Fuser Type 1

Make sure fuse is installed correctly, Verfy proper fuser is being used. On the status window or LCD monitor (if it have) of printer shown on message: "Low heat error cycle power" This error is related to the fusing assembly. Tamas: Ok I'l get. Lexmark Fuser Replacement Replace the Autocompensator Assy.

Power printer off one to two minutes. 920.06 Service Fuser Error Check for 24V at red wire on interlock switch with door closed 4. Try opening Tray X. Replace Printhead Pricing Error 935 Printhead Error - May have sub-codes.

Remove jammed media How did we do? 922.02 Service Fuser Error I truly appreciate it. If the printer is already on a wall outlet, plugging the printer into a different outlet may solve the problem. Load correct size Error 28 Input sensor not made after pick attempt.

920.06 Service Fuser Error

Error 59 Duplex Cover Open Top cover of duplex unit is sensed open. https://www.marketpoint.com/lexmark-error-code-92x-service-fuser-error.aspx Error 923 Fuser is too hot while printing or when idle. • Short in the thermistor circuit. • Noisy thermistor signal • Fuser is actually overheating due to hardware faults. 924.01 Service Fuser Error Lexmark Indicates that the fuser is below standby temperature when the printer is idle. Service Fuser Error Lexmark Printer Scroll Down to your error code....

To order this part please click here.http://www.iteminc.com/itemdesc.asp?i...For any other printer needs visit us at http://www.iteminc.com Κατηγορία Επιστήμη και τεχνολογία Άδεια Τυπική άδεια YouTube Εμφάνιση περισσότερων Εμφάνιση λιγότερων Φόρτωση... Διαφήμιση Αυτόματη αναπαραγωγή have a peek at these guys fastprintersdotcom 70.941 προβολές 5:28 Desarme lexmark x26x36x P3 - Διάρκεια: 11:42. May be due to the paper feeding manually while motors running and previous page in path. Error 920.X and 922.XX may display for a cold fuser. Lexmark X654de Service Fuser Error

However, it does not work properly. If this does not clear up the fuser error, the problem may be in one of the following: the fuser cover assembly the engine board the DC fuser cable the fuser P.H.U. check over here The heated roller is heated by a halogen lamp or in some cases a solid state ceramic heating element and is subject to failure.

Verify correct cable connections from the Engine board to the HVPS. 122.02 Service Fuser Error Purchasing information:  Lexmark T640 , T642, T644 series fuser and maintenance kitPurchasing information:  Lexmark T650 , T652, T654 series fuser and maintenance kit Tech Support Support Home PageMaintenance Kit InstructionsOther instructionsTroubleshootingArticles, Make sure the printer is plugged straight to the wall and not through a surge device or power strip.

You can change this preference below. Κλείσιμο Ναι, θέλω να τη κρατήσω Αναίρεση Κλείσιμο Αυτό το βίντεο δεν είναι διαθέσιμο. Ουρά παρακολούθησηςΟυράΟυρά παρακολούθησηςΟυρά Κατάργηση όλωνΑποσύνδεση Φόρτωση... Ουρά παρακολούθησης Ουρά __count__/__total__ Lexmark

Error 939 RIP Communications Lost Controller Engine Communications Lost The controller board and the engine board cannot communicate with one another. Remove jammed media Error 250 Paper Jam - Check MP Feeder Paper is jammed in the multipurpose feeder. Use caution when measuring AC voltages. 925 Service Fuser Error Lexmark T632 To verify that the printer recognizes all the installed memory, go to the user menus and print the “Print Menus” test page.

Keep in mind that there is no need to have the printer connected to a computer during testing for a fuser error as any pages to test the functionality of the Check paper sensor flag for restricted movement or damage. And how to fix error: a. http://cdbug.org/fuser-error/lexmark-fuser-error-136.php If either the 936 error or the 937 error returns after you power on the printer or when you try to print, the printer will require service.

Paper is either not leaving the duplex entry sensor in time or not making or unmaking the duplex exit sensor in time.