Home > Fuser Error > Lexmark Optra T614 Fuser Error

Lexmark Optra T614 Fuser Error


Error 922 Fuser failed to reach standby temperature. Loading... Working... Intterconnect Board Error 940-943 Color Machines Toner Metering Cycle failure CMKY cartridge 940 = Cyan cartridge 941 = Magenta cartridge 942 = Yellow cartridge 943 = Black cartridge Toner metering cycle check over here

Check the thermistor resistance at engine board J8-3 to J8-4; it should be from 100K Ohms to 260K Ohms when cold; it may be as low as 2.3K Ohms when hot See if there is any paper or any other item stuck there that could be causing the fuser unit to overheat. Replace the bump alignment motor Replace bump motor Replace interlock switch Replace System Card Error 230 Paper Jam - Check Duplex The paper is most likely jammed in the Duplex Error 58 Duplex Not Attached Duplex is electrically connected but no longer mechanically attached, and printer top cover is closed.

920.06 Service Fuser Error

Replace printhead, system board or ribbon cable. Surge protectors and power strips can sometimes regulate the voltage to a fault for the printer. Error 80 Printer has reached 200,000-300,000* prints without maintenance count reset.

Sign in to add this to Watch Later Add to Loading playlists... 3567 Benton Street, Suite 243 Santa Clara, CA 95051 800.360.1337 408.745.9800 Order Desk: 8 AM to 5 PM Home Power printer off one to two minutes. Additional info on X and XX codes available by email. 922.02 Service Fuser Error It is necessary to replace the fuser assembly, transfer roller, and charge roll at this interval to maintain the print quality and reliability of the printer.

The main motor is located just to the left of the toner cartridge. 924.01 Service Fuser Error Also, if the accumulated sheets are removed, the portion of the job printed after the jam will not be stapled. If you cannot find anything jammed up or broken in the back of the printer,open the upper front cover of the printer and remove the toner cartridge. http://support.lexmark.com/index?page=content&id=SO4036&modifiedDate=11/14/13 Close Yeah, keep it Undo Close This video is unavailable.

sometimes just powering it off, then on clears the error message, but it just shows up again soon. 122.02 Service Fuser Error Back to Service Error Code List Source: Lexmark KnowledgeBase Home Page Technical Resources Lexmark Error Codes HP Error Codes Tech Support Blog HP Drivers Lexmark Drivers Terms & Conditions Product No inkjet error codes available Error Code Error Message Solutions ERROR 20 ERROR 200 Input Paper Sensor was not triggered - Paper may be jammed at the sensor. I replaced the fuser about a year ago, and had no problems with it until we moved into the new building (about 6 weeks ago).

924.01 Service Fuser Error

Controller Board 2. http://www.fixyourownprinter.com/posts/62680 Error 63 Unformatted or Defective Disk The printer will ignore a disk it senses as defective. 920.06 Service Fuser Error All rights reserved. Lexmark X654de Service Fuser Error Sign in Transcript Statistics 5,121 views 0 Like this video?

Reconnect. check my blog If this is an intermittent error, you may want to check how the printer is plugged in, even ifit has worked on this surge device for months. Sign in to add this video to a playlist. Run the Quick Disk Test. Lexmark Fuser Replacement

Make sure that nothing is stuck inside the fuser unit that cancause the fuser unit to overheat. Tray is empty or not installed, paper jam in entry throat, or printer is requesting a manual feed. Make sure fuse is installed correctly, Verfy proper fuser is being used. this content If it happened with a new fuser it would imply the wrong fuser type.

Error 59 Duplex Cover Open Top cover of duplex unit is sensed open. 925 Service Fuser Error Lexmark T632 Check AC power source for noise. Use caution when measuring AC voltages.

Request Quote 947 Engine Board Engine board failure Replace the Engine Board Request Quote 953-954 NVRAM Failure NVRAM Failure 953: NVRAM Chip Failure 954: NVRAM CRC Failure Optra T 640/642/644

Bowers Baldwin 5,411 views 8:27 Vídeo Recarga Toner Lexmark T630 | T640 | T642 | T644 | X642 | X644 - Vídeo Aula Valejet.com - Duration: 6:34. If one of these errors appeared during POST, or while the printer was idle (not printing or receiving data), or while trying to print one of the internal test pages, replace Loading... Lexmark Support Check fan connector and cable for loose or damaged connection.

Error 62 Disk Full Not enough disk space for data that has been requested to be written to disk. valejet TV 35,197 views 6:34 Lexmark T630 T640 Series Printer paper pick-up drive replacement.wmv - Duration: 3:40. If this does not clear up the fuser error, the problem may be in one of the following: the fuser cover assembly the engine board the DC fuser cable the fuser http://cdbug.org/fuser-error/lexmark-optra-s-1855-fuser-error.php Featured Post 6 Surprising Benefits of Threat Intelligence Promoted by Recorded Future All sorts of threat intelligence is available on the web.

Remove jammed media Error 90X Software Error Unrecoverable software error. Transfer Roll Error Cannot start servo operation. Call us with any questions toll-free 866-352-7108 or local 608-831-2396. Check LVPS cable for continuity.

It should stay at 0 until the 922 Error is displayed and then go to +5 VDC; if it does not,replace the engine board, the fuser, and the fuser wiper. Check for 24V at red wire on interlock switch with door closed 4. Check paper sensor flag for restricted movement or damage. Power strips and uninterrupted power supplies can cause a low amperage problem in your printer whichcan trigger a false fuser error.

ValstarPrinters 7,608 views 3:40 how Laser Technology Process animation - YouTube.WEBM - Duration: 2:56. We got it this morning and I have it installed. A secondary error indication can be obtained by pressing an releasing a button. If not present check in printer.

Error 939 RIP Communications Lost Controller Engine Communications Lost The controller board and the engine board cannot communicate with one another. Reconnect. this happens usually (but not always) after a paper jam, which is happening quite often. Lexmark Fuser Pricing Error 925 A 925 service error indicates the wrong fuser lamp is installed in the printer and does not match the one stored in the printer code.

Any help here would be appreciated too. Loading... If there is no continuity, make sure the HVPS contact returns to its upward limit when depressed, and make sure the left bearing of the transfer roll is making proper contact. Please try again later.

Remove toner cartridge for better access to jammed paper.