Home > Konica Minolta > Konica Error Messages

Konica Error Messages

Contents

The printer has only printed 1430 pages since I got it a little over a year ago. We have had this problem on numerous 23xx and 24xx printers, where the sensors get covered in toner dust and therefore can't report status so the printer thinks it's empty.We clean where is the container located on rhis printer. Both the printer and the computer's printer driver settings (under Win/XP) are set to Letter. Source

Do this... The error message is the same for each scan, but the error code varies. Please help anyone! Restore password × Upload manual upload from disk upload from url Thank you for your help! additional hints

Bizhub Error Codes

I'm not a tech type person but would like some ideas to what may be happening and also how to fix? The unit is now apart to the laser unit. The second problem is the presence of small black smudges about 2 inches from the bottom. I'm no printer tech, but in most other lasers (HPs, etc) the paper tray lifts, or pushes up a little on the paper stack, via springs, coils, or other mechanical means.

It kind of looks like multicolored barcode from top to bottom of page with all the lines extending from left edge in about 1/2 - 3/4". bad roller? by sailerman on Oct 29, 2009 at 6:51am Add comment Please sign in to comment 1 i just installed a new opc drum on my konica minolta magicolor 2400w; yet it Konica Minolta C451 Error Codes List If this still does not fix the problem, remove the feed tire (it's dark grey and looks like a half moon) and clean it with some rubber renue or windex.

Not a job for the faint-hearted as it's hard to get to, and the switch is not exactly robust. Has anyone else experienced the same scan issue with a printer? Good luck. - Anonymous It got out of alighnment - reboot it (turn it off and on) and it should go away - Anonymous 6 Am working on a Magicolor 2300 Join Now Hi all, We installed a new Konica Minolta printer this spring (model number is bizhub C224e). The printer was scanning just fine until one day when the executive assistant reported

I changed the paper size in the printer menu to a 10 inch length and the paper eject fine. Konica Minolta C452 Error Codes We have seen this seemingly "fake" media jam issue in the 2300DL for a year now ("fake" because the paper never gets picked up and so never actually "jams", but whatever).It I keep wiping it away, but a couple of times every day the printer stops working and reports that the [say] Black cartridge is not installed. If we pile in paper to the maximum height, paper picks up OK.

Konica Minolta Error Deletion

What should I replace? Helpful (1) Reply options Link to this post by im4GMG, im4GMG Jan 27, 2011 11:41 AM in response to PAHU Level 1 (0 points) Jan 27, 2011 11:41 AM in response Bizhub Error Codes Black too.What does that? Konica Minolta Error Code 107 Also do you refill your toners?

After applying the pressure or hitting with a mallet load with paper, turn on and see what happens. this contact form Does this indicate a problem with the optica sensor? A couple of clicks and problem solved. I check the drum and it still looks good. Konica Minolta Server Connection Error Scan Email

the specified folder does not exist).1003The target resource is a collection (directory).1011Although "https" is specified for the resource URL, it is unavailable because the SSL library is not included for the It leaves me to beleive it is the scanner within the printer causeing this issue. by dmzcompute on Oct 22, 2006 at 6:47pm Add comment Please sign in to comment Thanks, Excellent Solution, fixed my problem in 2 seconds. - justchecking 1 Hi,I have a minolta have a peek here Copier repair in Salt Lake City, YP, Utah.

I'm on a Mac OS 10.6. Konica Minolta Bizhub Pro 951 Error Codes Thanks in Advance for any help. by S.Smith on May 9, 2016 at 12:07pm Add comment Please sign in to comment 0 Hi!I have KM Pagepro 1300W printer, and prints dirty pages.I tried to print with another

The lines I describe as looking like barcode are all parallel to each other and perpendicular to the paper path.

As the paper feeds I can hear it getting "stuck". Are you kidding me? 1 Pimiento OP brandoncarr2 Oct 23, 2015 at 5:29 UTC 1st Post this is a very simple fix. Make sure it is in a like up position ready to be pressed down by the paper moving thru the printer. Konica Minolta Result Ng Do you know the maximum size drive that can be installed?

due to insufficient server capacity).SMB transmission42The protocol is not initialized.52MIO was reset during forwarding.55An I/O buffer capacity shortage occurred.57Failed to connect to the server.62The device is not connected to the network.The I realized the tonor rack was getting jammed against these two plastic tabs that are attached to the inside of the door on the front face of the printer (presumably for Go to the Network tab, and leads to a corresponding state. http://cdbug.org/konica-minolta/konica-minolta-magicolor-2430dl-error-messages.php Hope it helps!

I looked and the toner is not turning. After enabling it scanning worked. 0 Sonora OP stephenbrown2 Jul 3, 2014 at 4:09 UTC When you look at the Job List, you should be able to select Is there an exploded diagram that would show the sensor? Thanks by blkwhthusky on Dec 20, 2011 at 9:00am Add comment Please sign in to comment 1 I have a bizhub pro C6000 that I got new in 2011.

I couldn't find one on the Konica Minolta site. I've also various drivers to no avail, from the latest version of the BizHub driver (v.3.2), to the Generic PCL and Generic PostScript drivers in Mac OS X.I'm adding the printer Do not know what to do.Help and Thanks by Anonymous on Feb 24, 2007 at 2:46pm Add comment Please sign in to comment Sound like your ITB cleaning blade has failed Recently the printing started to print a couple of inches below the set margin and then the bottom of the page text gets cut off.

It started printing with greenish yellow blots streaked along the page verically. Look for any plastic moving parts which look like they move in the direction of the paper path and then should return by spring action towards the oposite direction. its the contact sensor, find it on the imaging unit,> then clean the corresponding on inside the printer (it's> easier to find it outside of the printer if you don't know> These levers reduce fuser pressure, and if theyare in the up position (i.e.

When I checked the print log (not sure why I didn't think to do this earlier), it showed my jobs deleted because of a "Login Error." I thought of the security