I have taken so many things off and put them back on, banged, clanged, snapped, crackled and popped everything I can see on both of them and still the error won't Can someone please help. I can’t work out where this grey dust is coming from (it seems to be waste toner, and is more concentrated toward the right-hand side of the printer internals). by ccscomputers on Jan 6, 2011 at 12:57pm Add comment Please sign in to comment 1 I have a net connected 5430DL, it will boot up and the 'Ready' light will have a peek here
Koli S.C. 6.129 προβολές 2:21 [Tutorial] Como Instalar fotocopiadora Konica Minolta bizhub como Impresora - Διάρκεια: 28:00. I love the printer, however when I try to print a color that covers a large area, tracks seem to be down the entire page instead of a smooth covering. by jeffreyandrew on Apr 14, 2008 at 7:48pm Add comment Please sign in to comment Considering that not too long ago, I saw these at Fry's for $149 refurbished, it makes I rang Konica Minolta and they sent a technician to fix for free (the phone number is 1800 456 999), so check when you purchased your machine - I thought it
Often, the page does not fully exit the printer and I must extract the sheet and open/close the top to get the printer running again. Back to top #10 Broni Broni The Coolest BC Computer BC Advisor 41,185 posts ONLINE Gender:Male Location:Daly City, CA Local time:08:02 PM Posted 02 March 2010 - 04:08 PM and Take it out and replace it with a Radio Shack Fuse # 270-1046 it is a Fast acting fuse 0.316 amps GMA style 20mm.
These flags can get pushed behind and so it reports a media jam, even without the paper. Can anyone please help with the set of error codes? I tried both drivers as default and still same result. Question about Konica Minolta PagePro Printers & Copiers 1 Answer Ready light on.
Any ideas will be greatly appreciated, TY. by chrisjon on May 14, 2007 at 12:10am Add comment Please sign in to comment 0 Hi all, I have a magicolor 2400w that when it prints leaves a faint 1/4" It's only mentioned right above your post. - Anonymous 0 Hi, thanks: I'm using the duplex accessory -- do I need to remove it and go into the case from the
Back to top #14 Broni Broni The Coolest BC Computer BC Advisor 41,185 posts ONLINE Gender:Male Location:Daly City, CA Local time:08:02 PM Posted 02 March 2010 - 04:36 PM This
Search Fixya Press enter to search. giri klk 13.244 προβολές 1:40 Konica Bizhub C451 / 43K 176K - Διάρκεια: 2:05. Comment Was this review helpful to you? i don't believe this was the caus e of error light this time.
Also do you refill your toners? read review Sometimes even then it jams. I have it installed on XP, have not done so on Win 7 yet. And, I couldn't identify an issue with the gears not being meshed that engineer1000 posted was the fix for him.
Can it be replaces. navigate here Take out the consumables and toss it. And since it has happened to both machines then I thought this may be a common problem that someone might have experienced. We saw nice solid text with crisp edges in our tests, although some bold lettering almost merged.
Back to top BC AdBot (Login to Remove) BleepingComputer.com Register to remove ads #2 Broni Broni The Coolest BC Computer BC Advisor 41,185 posts ONLINE Gender:Male Location:Daly City, CA by unknown on Oct 4, 2008 at 8:27pm Add comment Please sign in to comment 1 I have a model 2300w which is having two problems. worked fine, but had very little life left and is now asking to be replaced.Can I take the reset chip from the new unit and put in the old unit and Check This Out I haven't done this before, so any help would be appreciated!!
I have removed the toner and I can't see anything stuck inside. Good luck. - Anonymous It got out of alighnment - reboot it (turn it off and on) and it should go away - Anonymous 6 Am working on a Magicolor 2300 I couldn't see what the error was exactly, as I was running it in Linux, so I do not have the status monitor.Now it will not even finish booting - it
The Konica Minolta 2430 printer comes with a 2-year warranty. by unknown on Sep 20, 2007 at 10:59am Add comment Please sign in to comment it works off opto sensor. Print This PagePrint ShareShare Url of this page: HTML Link: Bookmark Manuals Brands Konica Minolta Manuals Printer PagePro 1400W User manual Konica Minolta PagePro 1400W User Manual: Status Messages (ready Indicator, It looked almost impossible to get them out without damage so I just shorted across the plates with a single core wire stiff enough to secure it.
I am unable to find or recognize the contact sensor. It installed and did not ask me to connect it. It will not do thousands of prints a month or a day without paper feed problems. http://cdbug.org/konica-minolta/konica-1400w-error.php Plugged in and bingo, it worked.I now think that pressing some aluminium foil in the gap between the metal plates would have also done the job.
I likewise attempted to clean the mating switch contact in the printer, but noticed that one of the contacts was mis-aligned. Yes No Sending feedback... Had to force the door closed but it seems to be working o.k.. by Anonymous on Nov 27, 2007 at 8:43pm Add comment Please sign in to comment 0 Hi, Sorry - I am only a user with some knowledge of 2300w and 2400w
Black too.What does that? Open up the door and remove the drum assembly. Along with the noise the error light started flashing quickly. Thank you for your feedback.
My toners are all healthy and i have gently shaken them to make sure no clogging.