Home > Lens Error > Lens Error Restart Camera Casio Exilim

Lens Error Restart Camera Casio Exilim

Sign in Transcript Statistics 40,526 views 25 Like this video? And don't forget to also visit our YouTube channel! January 28, 2008 at 3:18 AM Sara said... There's a halfway chance of fixing it yourself, described here: http://camerarepair.blogspot.com/2007/12/fixing-lens-error-on-digital-camera.html ... weblink

Sonny DSC-W55:lens gets stuck occasionally on start-up. Usually w/o any parts. There are some DIY solutions you could try, but the \012probability is that you will have to get it fixed by a professional. ... Put a fresh set of batteries back in (preferably rechargeable NiMH 2500mah or better) and turn the camera on.

I DID CHANGE THE BATTERIES. Pay particular care not to scratch your lens barrel with the needle. hope this helps April 18, 2008 at 1:28 PM Anonymous said... I have a Sony Cyber Shot and was about 10 seconds away from buying a new camera till I saw your site.

I have a Casio Exlim EX S600. Sometimes the lens won't even move. Casio Exilim Lens Error/Retry Power On By RJ The Bike Guy Published: 4 years ago I would occasionally get lens errors or retry power on messages on my Casio Exilim digital First review the warnings in the "Please Read This First" section of this blog, especially the flash capacitor shock warning and link.

If the AV cable doesn't fix the lens error by itself, consider keeping this cable installed while trying fixes 4, 5, and 7 as a means to provide extra help to Easy Quick Works! - Duration: 2:22. And while it should be obvious that anything can potentially fail [in infinite variation] typically, it's moving parts and poor contacts that are at fault -- And your site nailed it Take a picture and view it on your computer using a card reader.

But thought it won't hurt to try...Canon A510..powers on, shows the canon screen, lens stuck (almost all the way in except for maybe about 3/16 of an inch)then powers off. you'll come short. Fix #4: Place the camera flat on its back on a table, pointed at the ceiling. Any step-by-steps you can give?

Graham Houghton 247,633 views 31:21 tutorial reparación de cámara digital canon sd1300 error de reinicie la cámara 1/5 - Duration: 8:54. You're amazing and I'm so grateful. February 10, 2008 at 2:47 AM Camera Repair said... March 7, 2008 at 10:13 AM jonno said...

If you feel brave, try it. http://cdbug.org/lens-error/lens-error-please-restart-camera.php Watch QueueQueueWatch QueueQueue Remove allDisconnect Loading... And remember, these fixes (especially #6 and 7) should only be considered for a camera that's out of warranty, who's cost of repair would be excessive, and would otherwise be considered June 11, 2008 at 12:14 PM Anonymous said...

Using a blow-dryer didn't work and neither did changing the batteries. I was sitting on the floor and it slipped from my hand while the lens was out. I just hope I didn't damage the lens in all the fiddling I was doing with it prior. http://cdbug.org/lens-error/lens-error-restart-camera.php THEN I TURNED IT ON AND IT WORKED!

What is the problem? Fully charged batteries that work fine in other cameras, seem to give the Casio problems. March 21, 2008 at 10:02 AM Camera Repair said...

Turned off camera and performed slightly-more-than-gentle twisting of the lens.

Rating is available when the video has been rented. Result "zoom error" on screen, lens stuck halfway and the outer segment was at a strange angle. Kamera-Station.de Canon PowerShot S100 Lens Error E32 Reparatur / Repair: By KAMERA HANDY STATION Published: 1 year ago www.kamera-station.de E32 bedeutet Anti-Shake defekt. When I turned it on after that I still saw the "lens error", so I applied "gentle" pressure to the lens while it was open.

Again, this didn't work for me, I suspect the grit has ended up in the cogwheels below the barrels. Fix #6: Repeatedly tap the padded/rubber usb cover on a hard surface with the intent of dislodging any particles that may be jamming the lens. This feature is not available right now. this content Downloaded the Advance Guide and that is how I found out what the message means, but what can I do?

Loading... on start-up.